ohif-viewer/platform/docs/versioned_docs/version-3.10/configuration/url.md

---
sidebar_position: 3
sidebar_label: URL
---

# URL

You can modify the URL at any state of the app to get the desired result. Here
are different part of the APP that you can modify:


## WorkList

The WorkList can be modified by adding the following query parameters:

### PatientName

The patient name can be modified by adding the `PatientName` query parameter.

```js
/?patientName=myQuery
```

### MRN

The MRN can be modified by adding the `MRN` query parameter.

```js
/?mrn=myQuery
```

### Description

The description can be modified by adding the `Description` query parameter.

```js
/?description=myQuery
```

### Modality

The modality can be modified by adding the `modalities` query parameter.

```js
/?modalities=MG
```

### Accession Number

The accession number can be modified by adding the `accession` query parameter.

```js
/?accession=myQuery
```

### DataSources

If you happen to have multiple data sources configured, you can filter the
WorkList by adding the `dataSources` query parameter.

```js
/?dataSources=orthanc
```

Note1: You should pass the `sourceName` of the data source in the configuration file (not the friendly name nor the name)
Note2: Make sure that the configuration file you are using actually includes that data source. You cannot use a data source from another configuration file.


:::tip

You can add `sortBy` and `sortDirection` query parameters to sort the WorkList

```js
/?patientName=myquery&sortBy=studyDate&sortDirection=ascending
```

:::


## Viewer

The Viewer can be modified by adding the following query parameters:


### Mode

As you have seen before, the Viewer can be configured to be in different modes.
Each mode registers their `id` in the URL.

For instance

```js
/viewer?StudyInstanceUIDs=1.3.6.1.4.1.14519.5.2.1.7009.2403.871108593056125491804754960339
```

will open the viewer in the basic (longitudinal) mode with the StudyInstanceUID
1.3.6.1.4.1.14519.5.2.1.7009.2403.871108593056125491804754960339.

And if configured, the same study can be opened in the `tmtv` mode

```js
/tmtv?StudyInstanceUIDs=1.3.6.1.4.1.14519.5.2.1.7009.2403.871108593056125491804754960339
```

### StudyInstanceUIDs

You can open more than one study in the Viewer by adding the `StudyInstanceUIDs`


```js
/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095722.1&StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095258.1
```

:::tip

You can use this feature to open a current and prior study in the Viewer.
Read more in the [Hanging Protocol Module](../platform/extensions/modules/hpModule.md#matching-on-prior-study-with-uid) section.  You can also use commas to separate
values.

:::


### SeriesInstanceUIDs

Sometimes you need to only retrieve a specific series in a study, you can do
that by providing series level QIDO query parameters in the URL such as
SeriesInstanceUIDs.  This does NOT work with instance or study
level parameters.  For example:

```js
http://localhost:3000/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095438.5&SeriesInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095449.8
```

This will only open the viewer with one series (one displaySet) loaded, and no
queries made for any other series.

Sometimes you need to only retrieve a subset of series in a study, you can do
that by providing more than one series, separated by commas.  For example:

```js
http://localhost:3000/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095438.5&SeriesInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095449.8,1.3.6.1.4.1.25403.345050719074.3824.20170125095506.10
```

This will only open the viewer with two series (two displaySets) loaded, and no
queries made for any other series.

### initialSeriesInstanceUID

Alternatively, sometimes you want to just open the study on a specified series, but allowing other
series to be present too.  This is the same behavior can be
achieved by using the `initialSeriesInstanceUID` parameter.  For example:

```js
http://localhost:3000/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095438.5&initialSeriesInstanceUID=1.3.6.1.4.1.25403.345050719074.3824.20170125095449.8
```

This will open all the series in the study, but the viewer will start with the
series specified by the `initialSeriesInstanceUID` parameter.


Note that you can combine these, if you want to load a specific set of series
plus show an initial one as the first one selected, for example:

```js
http://localhost:3000/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095438.5&SeriesInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095449.8,1.3.6.1.4.1.25403.345050719074.3824.20170125095506.10&initialSeriesInstanceUID=1.3.6.1.4.1.25403.345050719074.3824.20170125095506.10
```

### initialSopInstanceUID

You can also specify the initial SOP Instance to be displayed by using the
`initialSopInstanceUID` parameter.  For example:

```js
http://localhost:3000/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095438.5&SeriesInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095449.8&initialSopInstanceUID=1.3.6.1.4.1.25403.345050719074.3824.20170125095501.9
```

This will open the study with the filtered series, and navigate to the slice 101
which happens to be the SOP Instance specified by the `initialSopInstanceUID`

Note: again you can mix and match

```js
http://localhost:3000/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095438.5&SeriesInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095449.8,1.3.6.1.4.1.25403.345050719074.3824.20170125095506.10&initialSeriesInstanceUID=1.3.6.1.4.1.25403.345050719074.3824.20170125095506.10&initialSopInstanceUID=1.3.6.1.4.1.25403.345050719074.3824.20170125095510.8
```

You can even load the whole study and only specify the initial SOP Instance to be displayed. Although
it will take more time to match, but it works as expected.

```js
http://localhost:3000/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095438.5&initialSopInstanceUID=1.3.6.1.4.1.25403.345050719074.3824.20170125095510.8
```

### hangingProtocolId

You can select the initial hanging protocol to apply by using the
hangingProtocolId parameter.  The selected parameter must be available in a
hangingProtocolModule registration, but does not have to be active.

For instance for loading a specific study in mpr mode from start you can use:

```js
http://localhost:3000/viewer?StudyInstanceUIDs=1.3.6.1.4.1.25403.345050719074.3824.20170125095438.5&hangingProtocolId=@ohif/mnGrid
```

### token

Although not recommended, you can use the token param in the URL which will inject
the token into the Authorization header of the request.